Blog

Repeater Firmware v1.18.0: Solar Nodes and Maintenance Tools

Repeater firmware v1.18.0 is out, and the community threads that followed show where hobbyists are putting their effort. They are building solar repeater nodes that survive winter, and they are asking for better tools to maintain them. The official release notes are the place to check before flashing anything on a mast, and the GitHub release page has the release itself.

First reports on the latest repeater firmware

Early feedback is thin. One Heltec V4 owner reported that telemetry stayed at 56% battery and 117°F temperature after flashing v1.18.0. That is a single report, not a confirmed bug, but anyone with a telemetry-dependent solar node should flash a test unit first.

Third-party projects are already building on the release. MatterMesh OS, a standalone firmware for the LilyGO T-Deck Max, is running on MeshCore 1.18.0. A T-Deck Plus update (0.4.0.14) added a companion link that pairs the T-Deck with another radio over Bluetooth, so a Wio with a better antenna can do the transmitting. It also shows which repeaters picked up your advert.

Solar repeaters are where the troubleshooting happens

Scroll through the recent builder threads and power comes up constantly. One RAK 1W owner runs three 6V panels in parallel into a 10,000 mAh LiPo behind a Waveshare solar board. The app never shows more than a few hours of uptime, even though the repeater never appears to power down. Another builder suspects the newer FCC-compliant 1W booster board limits output, which would change the old “10W panel plus big battery” recipe.

Cold climates raise a harder question: is active battery heating worth the energy it burns? A Reddit thread on solar repeaters in cold climates asks exactly that, and it matters for anyone north of the Alps. A Norwegian builder tackled the maintenance side differently with a roofed “docking station” that hoists a repeater up a tree, so a winter fix does not mean climbing six metres.

Simpler hardware choices keep recurring too:

  • Heltec T114 builds inside repurposed 4W solar-light enclosures with a 2600 mAh cell
  • 21700 cells considered in place of 18650s in 1W RAK builds
  • Inserts for the common junction boxes, with slots for an 18650 BMS
  • Power over Ethernet as a battery-free alternative

The PoE builder runs 50 ft of Ethernet to a rooftop RAK 1W and converts the power to 5V with a splitter inside the case. They report one-hop neighbours 30 km away. If mains and a cable run are available, it removes the battery question entirely. The repeater guide covers power options in more depth.

Updating repeaters without a ladder

Maintenance is the other theme. A community developer has published an alpha of firmware updates over LoRa, built on RFC 6206 (the Trickle algorithm). The author asks people to test on a spare repeater only, and anyone worried about airtime should read the project FAQ first.

MediaMesh, from CascadiaMesh, points the same way. It lets users send images and voice messages over the mesh, and it needs only a firmware update on local repeaters. Features may increasingly reach the network through repeater firmware.

Network hygiene: hash sizes and channel noise

Several threads touch the same operational issue. One user asked whether the nearest repeater, still set to 1-byte path hashes in an otherwise 2-byte area, could be hurting their sending and receiving. A reply said the setting mainly controls the hash size of the repeater’s own adverts, so it probably does not affect forwarding on current firmware. One operator whose mesh is being abused by someone hiding behind 1-byte hashes asked for a way to refuse forwarding those packets, and was told it is not currently possible. Another user asked whether blocking chatty channels like #test and #bot would save airtime.

Regional coordination is the long-term answer. Central Texas reports progress connecting Waco after its repeaters were moved back to default settings, and has put forward a draft regional-scope proposal. European groups can compare notes through the community page.

What it means for European builders

Several of these threads are North American and use FCC-compliant boards and US suppliers, so check 868 MHz equivalents and duty-cycle limits before copying a 1W build. The RAK 1W threads cited here concern the FCC-compliant boards.

Europe is not absent. A Berlin builder finished a rooftop rack at c-base running a Meshtastic router, a MeshCore repeater and a Reticulum access point. It is built around a Raspberry Pi with a LoRa hat, plus two Heltec V4 boards attached over USB serial. The builder plans to move to MeshCore natively once PR #2025 for native Linux targets merges; it was still open at the time of writing. For the Meshtastic trade-offs, see the comparison. New builders can start with the get started guide, browse supported devices, and check the coverage map for gaps worth filling.

The practical advice from these threads is to read the v1.18.0 release notes, update a bench unit before the rooftop one, and get the power budget right before worrying about the radio.